#!/bin/sh # rc.modules 3.0.1 Fri May 31 01:47:17 PDT 2002 pjv # # This file loads extra drivers into the Linux kernel. # The modules will be looked for under /lib/modules/ # On systems using KMOD this file will be mostly commented out, but is still # useful for loading selected modules at boot time. # # Most Linux kernel modules will accept extra options such as IRQ or base # address, or to set various modes (such as 10baseT or BNC, etc). The Linux # kernel source is the best place to look for extra documentation for the # various modules. This can be found under /usr/src/linux/Documentation if # you've the installed the kernel sources. Also, the kernel source docs are # present on the Slackware CD in the /docs/linux-2.x.x directory. # # NOTE: This may not be a complete list of modules. If you don't see what # you're looking for, look around in /lib/modules/2.x.x/ for an appropriate # module. Also, if any problems arise loading or using these modules, try # compiling and installing a custom kernel that contains the support instead. # That always works. ;^) # ### Update module dependencies ### RELEASE=`uname -r` # If /usr is mounted and we have 'find', we can try to take a shortcut: if [ -x /usr/bin/find -a -e /lib/modules/$RELEASE/modules.dep \ -a /lib/modules/$RELEASE/modules.dep -nt /etc/modules.conf ]; then NEWMODS="`/usr/bin/find /lib/modules/$RELEASE -type f -newer /lib/modules/$RELEASE/modules.dep`" # Only rebuild dependencies if new module(s) are found: if [ ! "" = "$NEWMODS" ]; then echo "New kernel modules have been found in /lib/modules/$RELEASE/:" echo "$NEWMODS" echo "Updating module dependencies for Linux $RELEASE:" /sbin/depmod -a else echo "Module dependencies up to date (no new kernel modules found)." fi else # we don't have find, or there is no existing modules.dep, or it is out of date. echo "Updating module dependencies for Linux $RELEASE:" /sbin/depmod -A fi #### APM support ### # APM is a BIOS specification for saving power using several different # techniques. This is mostly useful for battery powered laptops. #/sbin/modprobe apm #### PC parallel port support ### #if cat /proc/ksyms | grep "\[parport_pc\]" 1> /dev/null 2> /dev/null ; then # echo "parport0 is built-in, not loading module" > /dev/null #else # if [ -r /lib/modules/$RELEASE/misc/parport_pc.o \ # -o -r /lib/modules/$RELEASE/misc/parport_pc.o.gz \ # -o -r /lib/modules/$RELEASE/kernel/drivers/parport/parport_pc.o \ # -o -r /lib/modules/$RELEASE/kernel/drivers/parport/parport_pc.o.gz ]; then # # Generic setup example: # /sbin/modprobe parport_pc # # Hardware specific setup example (required for PLIP and better # # performance in general): # #/sbin/modprobe parport_pc io=0x378 irq=7 # fi #fi #### Parallel printer support ### #if cat /proc/ksyms | grep "\[lp\]" 1> /dev/null 2> /dev/null ; then # echo "lp support built-in, not loading module" > /dev/null #else # if [ -r /lib/modules/$RELEASE/misc/lp.o \ # -o -r /lib/modules/$RELEASE/misc/lp.o.gz \ # -o -r /lib/modules/$RELEASE/kernel/drivers/char/lp.o \ # -o -r /lib/modules/$RELEASE/kernel/drivers/char/lp.o.gz ]; then # /sbin/modprobe lp # fi #fi ### Parallel port IP ### #/sbin/modprobe plip ### AGP (Accelerated Graphics Port) GART support ### # This module takes care of programming the GART (part of your motherboard's # chipset that handles gathering data from memory and passing it to the # card) and enables faster AGP transfers. The AGP GART module is required # to use AGP features of your 3D rendering video card. You'll need this to # use XFree86's direct rendering support, for example. #/sbin/modprobe agpgart ### non-IDE CD-ROM drive support ### # These modules add CD-ROM drive support. Most of these drivers will probe # for the I/O address and IRQ of the drive automatically if the parameters # to configure them are omitted. Typically the I/O address will be specified # in hexadecimal, e.g.: cm206=0x300,11 # # ***NONE*** of these drivers are for use with IDE/ATAPI CD-ROM drives. That # support is already built into every pre-compiled Slackware Linux kernel. # Also, note that all of the manufacturers listed below stopped making these # types of wacky-interface drives years ago and all make IDE/ATAPI-interface # CD-ROM drives now. So, just because your drive says "Mitsumi" on it is not # reason enough to think you need the special Mitsumi module loaded, etc. If # you got your drive within the last couple of years it's probably IDE. Try # tossing a disc in the drive and mounting it on the various IDE interfaces it # could be using, like /dev/hdc. # #/sbin/modprobe aztcd aztcd= #/sbin/modprobe cdu31a cdu31a_port= cdu31a_irq= #/sbin/modprobe cm206 cm206=, #/sbin/modprobe gscd gscd= #/sbin/modprobe mcd mcd=, #/sbin/modprobe mcdx mcdx=, #/sbin/modprobe optcd optcd= # Below, this last number is "1" for SoundBlaster Pro card, or "0" for a clone. #/sbin/modprobe sbpcd sbpcd=,1 #/sbin/modprobe sonycd535 sonycd535= #/sbin/modprobe sjcd sjcd= # CD-ROM drives on ISP16, MAD16 or Mozart sound card: #/sbin/modprobe isp16=[[,[,]]][[,]] # where the values are one of: port=0x340,0x320,0x330,0x360 # irq=0,3,5,7,9,10,11 # dma=0,3,5,6,7 # drive_type=noisp16,Sanyo,Panasonic,Sony,Mitsumi ### Cyclades multiport serial card support ### #/sbin/modprobe cyclades #### Serial line IP support (SLIP/CSLIP/PPP) ### ## This module is for SLIP/CSLIP support: #/sbin/modprobe slip ## Load PPP: ## Check kernel version to determine module names to use #if [ "`uname -r | cut -f 1,2 -d .`" = "2.2" ]; then # # This module is for PPP support: # /sbin/modprobe ppp #else # assume 2.4 or newer # # This module is for PPP support: # /sbin/modprobe ppp_generic # # This PPP plugin supports PPP over serial lines: # /sbin/modprobe ppp_async # # Use this plugin instead for HDLC (used for high-speed leased lines like T1/E1) # # /sbin/modprobe ppp_synctty #fi ## This module provides compression for PPP (optional): ##/sbin/modprobe ppp_deflate ### USB Host Controllers: # Universal Host Controller Interface (Intel standard): #/sbin/modprobe usb-uhci # Universal Host Controller Interface (alternate JE): #/sbin/modprobe uhci # Open Host Controller Interface (Compaq/Microsoft/National standard): #/sbin/modprobe usb-ohci ### USB device support: # (Note that once you've loaded USB hub support most USB devices will # trigger the kernel to load their modules automatically) # USB "Human Interface Device" driver; handles most USB mice, joysticks, # gamepads, steering wheels, keyboards, trackballs and digitizers. #/sbin/modprobe hid # Simple HIDBP USB mouse driver, if hid doesn't work: #/sbin/modprobe usbmouse # Simple HIDBP USB keyboard driver, if hid doesn't work: #/sbin/modprobe usbkbd # Wacom Graphire and Intuos tablet driver: #/sbin/modprobe wacom # Logitech WingMan Force joystick: #/sbin/modprobe wmforce # USB audio: #/sbin/modprobe audio # USB modem support: #/sbin/modprobe acm # USB serial converter: #/sbin/modprobe usbserial # USB printer support: #/sbin/modprobe printer # IBM "C-It" USB video camera: #/sbin/modprobe ibmcam framerate=1 # USB OV511 Camera support: #/sbin/modprobe ov511 # USB ADMtek Pegasus-based ethernet device support: #/sbin/modprobe pegasus # Kawasaki USB ethernet controller support: #/sbin/modprobe kaweth # USB Kodak DC-2xx Camera support: #/sbin/modprobe dc2xx # USB Mustek MDC800 Digital Camera Support: #/sbin/modprobe mdc800 # USB Mass Storage support: #/sbin/modprobe usb-storage # USS720 parallel-port driver: #/sbin/modprobe uss720 # Prolific PL-2302 USB-to-USB network device: #/sbin/modprobe plusb # USB Diamond Rio500 support: #/sbin/modprobe rio500 # D-Link DSB-R100 FM radio support: #/sbin/modprobe dsbr100 # USB Bluetooth support: #/sbin/modprobe bluetooth # USB scanner support (requires patched SANE from http://fachschaft.cup.uni-muenchen.de/~neukum/scanner.html): #/sbin/modprobe scanner ### USB event drivers: # Keyboard input: #/sbin/modprobe keybdev # Mouse input: #/sbin/modprobe mousedev # Joystick input: #/sbin/modprobe joydev # Generic event reporting device: #/sbin/modprobe evdev ### Sound support ### # Sound Blaster Pro/16 support: #/sbin/modprobe sb io=0x220 irq=5 dma=3 dma16=5 mpu_io=0x300 # Sound Blaster Live support: #/sbin/modprobe emu10k1 # MAD16 support: #/sbin/modprobe mad16 io=0x530 irq=7 dma=0 dma16=1 # AD1816(A) sound driver: #/sbin/modprobe modprobe ad1816 io=0x530 irq=5 dma=1 dma2=3 ad1816_clockfreq=33000 # Crystal CS4232 based (PnP) cards: #/sbin/modprobe cs4232 # ES1370 support, such as Sound Blaster 128PCI: #/sbin/modprobe es1370 # ES1371 support, such as Sound Blaster 64V PCI: #/sbin/modprobe es1371 # ESS Maestro, Maestro2, Maestro2E: #/sbin/modprobe maestro # ESS Maestro3/Allegro: #/sbin/modprobe maestro3 # (For information on configuring other sound cards with Linux, # see the documentation in /usr/src/linux/Documentation/sound/, # and /usr/src/linux/Documentation/Configure.help. ### Joystick support ### # The core joystick input support module, needed by all of the # joystick devices below: #/sbin/modprobe joydev ### Next, you must load a module for your gameport. # Classic ISA/PnP gameports: #/sbin/modprobe ns558 # Crystal SoundFusion gameports: #/sbin/modprobe cs461x # Aureal Vortex and Trident 4DWave gameports: #/sbin/modprobe pcigame # SoundBlaster Live! gameports: #/sbin/modprobe emu10k1-gp ### Drivers for various joystick devices ### # Analog joysticks and gamepads: #/sbin/modprobe analog # Assassin 3D and MadCatz Panther devices: #/sbin/modprobe a3d # Logitech ADI digital joysticks and gamepads: #/sbin/modprobe adi # Creative Labs Blaster Cobra gamepad: #/sbin/modprobe cobra # Genius Flight2000 Digital joysticks and gamepads: #/sbin/modprobe gf2k # Gravis GrIP joysticks and gamepads: #/sbin/modprobe grip # InterAct digital joysticks and gamepads: #/sbin/modprobe interact # ThrustMaster DirectConnect joysticks and gamepads: #/sbin/modprobe tmdc # Microsoft SideWinder digital joysticks and gamepads: #/sbin/modprobe sidewinder ### Serial port game controller support ### # Both of these are needed for serial-port game controllers: #/sbin/modprobe serio #/sbin/modprobe serport # Logitech WingMan Warrior joystick: #/sbin/modprobe warrior # LogiCad3d Magellan/SpaceMouse 6dof controller: #/sbin/modprobe magellan # SpaceTec SpaceOrb/Avenger 6dof controller: #/sbin/modprobe spaceorb # SpaceTec SpaceBall 4000 FLX 6dof controller: #/sbin/modprobe spaceball # Gravis Stinger gamepad: #/sbin/modprobe stinger # I-Force joysticks/wheels: #/sbin/modprobe iforce ### Parallel port connected controllers ### # Multisystem, Sega Genesis, Saturn joysticks and gamepads: #/sbin/modprobe db9 # Multisystem, NES, SNES, N64, PSX joysticks and gamepads: #/sbin/modprobe gamecon # Multisystem joysticks via TurboGraFX device: #/sbin/modprobe turbografx ### Appletalk support ### # This is needed if you want to run netatalk, a package which allows # you to use you Linux box as a file and print server for Apple Macintosh # computers on your local network. #/sbin/modprobe appletalk ### IPX networking support ### #/sbin/modprobe ipx ### IDE device support ### # IDE CD-ROM drives: #/sbin/modprobe ide-cd # IDE hard drives: #/sbin/modprobe ide-disk # IDE floppy drives: #/sbin/modprobe ide-floppy # IDE tape drives: #/sbin/modprobe ide-tape ### Network device support ### # Most of these drivers will probe automatically for the card if you don't # specify an I/O address and IRQ. But, the NE2000 driver needs at least the # I/O. For complete information, see the net-modules.txt file that comes # with the Linux 2.2.x source code. This file can also be found on the # Slackware CD-ROM in the /docs/linux-2.2.x/ directory. # # First, if setup probing found a network card, there may be an 'rc.netdevice' # file that we should run to load the network module: if [ -x /etc/rc.d/rc.netdevice ]; then . /etc/rc.d/rc.netdevice fi ### Ethernet cards based on the 8390 chip. # 3com 3c503 support: #/sbin/modprobe 3c503 # Ansel Communications EISA 3200 support: #/sbin/modprobe ac3200 # Cabletron E21xx support: #/sbin/modprobe e2100 # HP PCLAN+ (27247B and 27252A) support: #/sbin/modprobe hp-plus # HP PCLAN (27245 and other 27xxx series) support: #/sbin/modprobe hp # NE2000/NE1000 support (non PCI): #/sbin/modprobe ne io=0x300 # NE2000 at 0x300 #/sbin/modprobe ne io=0x280 # NE2000 at 0x280 #/sbin/modprobe ne io=0x320 # NE2000 at 0x320 #/sbin/modprobe ne io=0x340 # NE2000 at 0x340 #/sbin/modprobe ne io=0x360 # NE2000 at 0x360 # PCI NE2000 clone support: #/sbin/modprobe ne2k-pci # SMC Ultra support: #/sbin/modprobe smc-ultra # SMC Ultra32 EISA support: #/sbin/modprobe smc-ultra32 # Western Digital WD80*3 (and clones) support: #/sbin/modprobe wd # # Other network hardware drivers: # # 3com 3c501 (consider buying a new card, since the 3c501 is slow, # broken, and obsolete): #/sbin/modprobe 3c501 # 3com 3c503: #/sbin/modprobe 3c503 # 3com 3c505: #/sbin/modprobe 3c505 # 3com 3c507: #/sbin/modprobe 3c507 # 3com 3c509 and 3c579: #/sbin/modprobe 3c509 # 3com 3c515: #/sbin/modprobe 3c515 # This one works for all 3com 3c590/3c592/3c595/3c597 and the # EtherLink XL 3c900 and 3c905 cards: #/sbin/modprobe 3c59x # Apricot Xen-II on board Ethernet: #/sbin/modprobe apricot # Generic ARCnet support: #/sbin/modprobe arcnet # AT1700/1720 support: #/sbin/modprobe at1700 # AT-LAN-TEC/RealTek pocket adapter support: #/sbin/modprobe atp # BPQ Ethernet driver: #/sbin/modprobe bpqether # Generic DECchip & DIGITAL EtherWORKS PCI/EISA: #/sbin/modprobe de4x5 # D-Link DE600 pocket adapter support: #/sbin/modprobe de600 # D-Link DE620 pocket adapter support: #/sbin/modprobe de620 # DEPCA support: #/sbin/modprobe depca # Digi International RightSwitch cards: #/sbin/modprobe dgrs # Intel EtherExpress Pro support: #/sbin/modprobe eepro # Intel EtherExpress PRO/100 PCI support: #/sbin/modprobe eepro100 # Intel EtherExpress16 support: #/sbin/modprobe eexpress # SMC EtherPower II 9432 PCI support: #/sbin/modprobe epic100 # ICL EtherTeam 16i/32 support: #/sbin/modprobe eth16i # DEC EtherWorks 3 support: #/sbin/modprobe ewrk3 # Fujitsu FMV-181/182/183/184 support: #/sbin/modprobe fmv18x # HP 10/100VG PCLAN (ISA, EISA, PCI) support: #/sbin/modprobe hp100 # IBM Tropic chipset based adapter support: #/sbin/modprobe ibmtr # AMD LANCE and PCnet (AT1500 and NE2100) support: #/sbin/modprobe lance # National Semiconductor DP8381x series PCI Ethernet support: #/sbin/modprobe natsemi # NI5210 support: #/sbin/modprobe ni52 # NI6510 support: #/sbin/modprobe ni65 # AMD PCnet32 (VLB and PCI) support: #/sbin/modprobe pcnet32 # Red Creek Hardware Virtual Private Network (VPN) support: #/sbin/modprobe rcpci # RealTek 8129/8139 (not 8019/8029!) support: #/sbin/modprobe 8139too # RealTek 8139C+ enhanced support: #/sbin/modprobe 8139cp # Sangoma S502A FRAD support: #/sbin/modprobe sdla # SMC 9194 support: #/sbin/modprobe smc9194 # TI ThunderLAN support: #/sbin/modprobe tlan # DECchip Tulip (dc21x4x) PCI support: #/sbin/modprobe tulip # VIA Rhine support: #/sbin/modprobe via-rhine # AT&T WaveLAN & DEC RoamAbout DS support: #/sbin/modprobe wavelan # Packet Engines Yellowfin Gigabit-NIC support: #/sbin/modprobe yellowfin ### Serial line load balancing support ### #/sbin/modprobe eql ### "dummy" IP support ### # A dummy IP driver. Essentially a loopback device. Can be useful -- # see the Network Administrator's Guide from sunsite.unc.edu:/pub/Linux/docs/LDP #/sbin/modprobe dummy ### ISDN kernel support ### #/sbin/modprobe isdn # ISDN loop (provides a virtual ISDN card for testing): #/sbin/modprobe isdnloop ### ISDN interface support ### # AVM-B1 with CAPI2.0 driver (requires additional firmware; see # /usr/src/linux/Documentation/isdn/README.avmb1): #/sbin/modprobe capidrv # HiSax SiemensChipSet driver (supports AVM A1, Elsa ISDN cards, # Teles S0-16.0, Teles S0-16.3, Teles S0-8, Teles/Creatix PnP, # ITK micro ix1 and many compatibles): #/sbin/modprobe hisax # IBM Active 2000 ISDN card support (requires additional firmware; see # /usr/src/linux/Documentation/isdn/README.act2000 for more information) #/sbin/modprobe act2000 # ICN active ISDN card driver: #/sbin/modprobe icn # PCBIT-D driver (requires additional firmware; see # /usr/src/linux/Documentation/isdn/README.pcbit for more information) #/sbin/modprobe pcbit # Spellcaster BRI ISDN driver: #/sbin/modprobe sc ### Binary format support ### #/sbin/modprobe binfmt_aout #/sbin/modprobe binfmt_elf #/sbin/modprobe binfmt_java #/sbin/modprobe binfmt_misc ### Filesystem support ### #/sbin/modprobe adfs #/sbin/modprobe affs #/sbin/modprobe coda #/sbin/modprobe ext2 #/sbin/modprobe fat #/sbin/modprobe hfs #/sbin/modprobe hpfs #/sbin/modprobe isofs #/sbin/modprobe minix #/sbin/modprobe msdos #/sbin/modprobe ncpfs #/sbin/modprobe nfs #/sbin/modprobe ntfs #/sbin/modprobe qnx4 #/sbin/modprobe romfs #/sbin/modprobe smbfs #/sbin/modprobe sysv #/sbin/modprobe ufs #/sbin/modprobe umsdos #/sbin/modprobe vfat ### RAID (Multiple Devices) support ### #/sbin/modprobe linear #/sbin/modprobe raid0 #/sbin/modprobe raid1 #/sbin/modprobe raid5 # *** THIS IS STILL LOADED BY DEFAULT *** # SCSI emulation support. This will provide SCSI host adapter emulation # for IDE ATAPI devices, and will allow you to use a SCSI device driver # instead of a native ATAPI driver. This is useful if you have an ATAPI # device for which no native driver has been written (for example, an ATAPI # PD-CD or CD-RW drive); you can then use this emulation together with an # appropriate SCSI device driver. Note that this option does NOT allow you # to attach SCSI devices to a box that doesn't have a SCSI host adapter # installed. Also, you'll need to exclude your CD-RW from being grabbed by # the normal ATAPI driver by passing a flag to the kernel at boot time. # If you're using LILO, add this: append="hdc=ide-scsi" # Replace "hdc" with the appropriate device name. /sbin/modprobe ide-scsi # SCSI kernel support: #/sbin/modprobe scsi_mod #/sbin/modprobe scsi_syms #/sbin/modprobe sd_mod #/sbin/modprobe sg #/sbin/modprobe sr_mod #/sbin/modprobe st # SCSI controller support: # NCR53c7,8xx SCSI support (note there is another driver for # the 53c8xx family below): #/sbin/modprobe 53c7,8xx # AM53/79C974 PCI SCSI support: #/sbin/modprobe AM53C974 # BusLogic MultiMaster and FlashPoint SCSI support: #/sbin/modprobe BusLogic # NCR53c406a SCSI support: #/sbin/modprobe NCR53c406a # Initio INI-A100U2W SCSI support: #/sbin/modprobe a100u2w # AdvanSys SCSI support: #/sbin/modprobe advansys # Adaptec AHA152X/2825 support: #/sbin/modprobe aha152x # Adaptec AHA1542 support: #/sbin/modprobe aha1542 # Adaptec AHA1740 support: #/sbin/modprobe aha1740 # This is support for the various aic7xxx based Adaptec SCSI # controllers. These include the 274x EISA cards; 284x VLB cards; # 2902, 2910, 293x, 294x, 394x, 3985 and several other PCI and # motherboard based SCSI controllers from Adaptec: #/sbin/modprobe aic7xxx # ACARD 870U/W SCSI support: #/sbin/modprobe atp870u # DTC 3180/3280 SCSI support: #/sbin/modprobe dtc # EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards) support: #/sbin/modprobe eata # EATA-DMA [Obsolete -- use above driver] (DPT, NEC, AT&T, SNI, AST, # Olivetti, Alphatronix) support: #/sbin/modprobe eata_dma # EATA-PIO (old DPT PM2001, PM2012A) support: #/sbin/modprobe eata_pio # Future Domain 16xx SCSI/AHA-2920A support: #/sbin/modprobe fdomain # Generic NCR5380/53c400 SCSI support: #/sbin/modprobe g_NCR5380 # GDT SCSI Disk Array Controller support: #/sbin/modprobe gdth # IOMEGA parallel port (imm - newer drives like ZipPlus): #/sbin/modprobe imm # Always IN2000 SCSI support: #/sbin/modprobe in2000 # Initio 91XXU(W) SCSI support: #/sbin/modprobe initio # AMI MegaRAID support: #/sbin/modprobe megaraid # NCR53C8XX SCSI support: #/sbin/modprobe ncr53c8xx # PAS16 SCSI support: #/sbin/modprobe pas16 # PCI2000 support: #/sbin/modprobe pci2000 # PCI2220i support: #/sbin/modprobe pci2220i # IOMEGA parallel port (ppa - older parallel Zip drives): #/sbin/modprobe ppa # PSI240i support: #/sbin/modprobe psi240i # Qlogic FastSCSI! cards: #/sbin/modprobe qlogicfas # QLogic ISP2100 SCSI support: #/sbin/modprobe qlogicfc # This driver works for all QLogic PCI SCSI host adapters (IQ-PCI, # IQ-PCI-10, IQ_PCI-D) except for the PCI-basic card. (This latter # card is supported by the "AM53/79C974 PCI SCSI" driver): #/sbin/modprobe qlogicisp # Seagate ST-02 and Future Domain TMC-8xx SCSI support: #/sbin/modprobe seagate # Symbios Logic sym53c416 support: #/sbin/modprobe sym53c416 # Trantor T128/T128F/T228 SCSI support: #/sbin/modprobe t128 # Tekram DC390(T) and Am53/79C974 (PCscsi) SCSI support: #/sbin/modprobe tmscsim # UltraStor 14F and 34F support (also see driver below): #/sbin/modprobe u14-34f # UltraStor 14F, 24F, and 34F support: #/sbin/modprobe ultrastor # Western Digital 7000 SCSI support: #/sbin/modprobe wd7000 ### Mouse support: # This is a rare type of busmouse that is connected to the back of an # ATI video card: #/sbin/modprobe atixlmouse # Logitech mouse connected to a proprietary interface card. It's # generally a round connector with 9 pins. Note that the newer mice # made by Logitech don't use the Logitech protocol anymore; for those, # you don't need this option: #/sbin/modprobe busmouse # Microsoft busmouse support. These animals (also called Inport mice) are # connected to an expansion board using a round connector with 9 pins. Be # aware that several vendors talk about 'Microsoft busmouse' and actually # mean PS/2 busmouse -- so count the pins on the connector: #/sbin/modprobe msbusmouse # C&T 82C710 mouse port support (as on TI Travelmate): #/sbin/modprobe qpmouse # IBM PC110 palmtop digitizer pad: #/sbin/modprobe pc110pad # Floppy drive support: # (Most Linux kernels should already contain this) #/sbin/modprobe floppy # Floppy tape support (such as Colorado Jumbo 250 or other QIC-80 drives): #/sbin/modprobe ftape # IP masquerading modules: # These modules are used with IP masquerading, a process which allows you to # use a Linux box connected to the Internet (via PPP or SLIP, or some other # means) as a gateway for other Linux, Windows, Macintosh boxes on your local # network that don't have real IP addresses on the Internet. The packets # going through the Linux machine are "masqueraded", or made to look as if # they're all coming from the one real IP address on the Internet. # # As a quick example (for a much more extensive treatment, see the IP-Masquerade # mini-HOWTO) to allow Internet access to a local network 192.168.11.0 with a # netmask of 255.255.255.0, you'd use these commands in /etc/rc.d/rc.local: # # echo 1 > /proc/sys/net/ipv4/ip_forward # echo "Setting up NAT (Network Address Translation)..." # # by default, nothing is forwarded. # ipchains -P forward REJECT" # # anything going from inside network to outside is masqueraded # ipchains -A forward -s 192.168.11.0/24 -d \! 192.168.11.0/24 -j MASQ" # # anything going from one internal machine to another can pass unmolested # ipchains -A forward -s 192.168.11.0/24 -d 192.168.11.0/24 -j ACCEPT" # # Then you'd have to set the other boxes on your local network to use the # Linux machine as their TCP/IP gateway. You'll probably also need to plug # in the IP address for your Internet service provider in each machine's DNS # setup. # # To use ipchains with newer kernels, you'll need this: #/sbin/modprobe ipchains # # Now, on to the IP masquerading modules. The example above is good enough # for most things that use TCP in a relatively simple fashion. It'll work # for telnet and http, for instance. But, the system breaks down when you # get protocols that use ports in more complicated ways. Luckily the Linux # kernel gurus have thought of this and have prepared some modules that # support masquerading of trickier protocols. The ipchains command is mighty # flexible as well, and a lot of things can be made to work just by setting # that up correctly. # ## These modules are in linux-2.2.x. Newer versions may use different modules. ## See also "man iptables" for information about a newer tool for Linux 2.4+. # #/sbin/modprobe ip_masq_autofw #/sbin/modprobe ip_masq_cuseeme #/sbin/modprobe ip_masq_ftp #/sbin/modprobe ip_masq_irc #/sbin/modprobe ip_masq_mfw #/sbin/modprobe ip_masq_portfw #/sbin/modprobe ip_masq_quake #/sbin/modprobe ip_masq_raudio #/sbin/modprobe ip_masq_user #/sbin/modprobe ip_masq_vdolive